暂无标题

LI Zhihui LIU Wentao LI Zhongyuan YANG Mingcheng GAO Xujing HE Suqin ZHU Chengshen

您当前的位置：

首页 >

文章列表页 >

暂无标题

更新时间：2021-12-01

- 暂无标题
- Journal of Radiation Research and Radiation Processing Vol. 31, Issue 2, Pages: 9-020303(2013)
- 作者机构：
  
  1. 1（郑州大学材料科学与工程学院）,郑州,450052
- 作者简介：
- 基金信息：
- DOI：
  CLC：
扫描看全文
LI Zhihui LIU Wentao LI Zhongyuan YANG Mingcheng GAO Xujing HE Suqin ZHU Chengshen. [J]. Journal of Radiation Research and Radiation Processing 31(2):9-020303(2013)
DOI：

LI Zhihui LIU Wentao LI Zhongyuan YANG Mingcheng GAO Xujing HE Suqin ZHU Chengshen. [J]. Journal of Radiation Research and Radiation Processing 31(2):9-020303(2013) DOI：

摘要

以N-异丙基丙烯酰胺（N-isopropyl acrylamide，NIPA）为单体，聚乙二醇（Poly (ethylene glycol)，PEG）为成孔剂，N, N-亚甲基双丙烯酰胺（N, N-methylene-bis-acrylamide，MBA）为交联剂，采用辐射聚合法制备出了一系列具有合适相转变温度的聚N-异丙基丙烯酰胺/聚乙二醇（Poly (N-isopropyl acrylamide)/Poly (ethylene glycol)，PNIPA/PEG）快速响应多孔智能水凝胶。用扫描电镜分析了该材料的表面形貌，研究了NIPA含量和PEG分子量对溶胀性能的影响，并以阿司匹林为模型药物研究了药物释放性能。结果表明：在该材料中存在大量孔洞，而未加成孔剂的水凝胶表面较为致密；该材料的溶胀率和失水率随NIPA含量的增大而逐渐减小，较低临界溶解温度（Lower critical solution temperature，LCST）和释药率都随PEG分子量的增大而逐渐增大，在PEG分子量为6000时，多孔水凝胶37℃下的释药率大于25℃，释药都符合Fickian扩散模式。

Abstract

A series of PNIPA/PEG (poly (N-isopropyl acrylamide)/poly (ethylene glycol)) porous intelligent hydrogels, which exhibited appropriate phase transition temperature and fast response behavior, were synthesized by radiation polymerization with NIPA (N-isopropyl acrylamide) as monomer, PEG (poly (ethylene glycol)) as pore-forming agent and MBA (N, N-methylene-bis-acrylamide) as crosslinking agent. The surface morphology of the material was examined by the scanning electron microscopy. The influences of NIPA content and PEG molecular weight on swelling properties were discussed. Drug release properties were studied with aspirin as a model drug. The results showed that macropores were observed in the sample, whereas hydrogels prepared without using PEG had a dense surface. The swelling ratio and water loss ratio of the sample decreased with increment of NIPA content. LCST (Lower critical solution temperature) and the release ratio increased with PEG molecular weight. The release ratio of PNIPA/PEG6000 hydrogel at 37℃ was larger than that at 25℃ and the release mechanism could be described with Fickian diffusion type.Cited

关键词

聚N-异丙基丙烯酰胺辐射聚合溶胀药物释放

Keywords

Poly (N-isopropyl acrylamide)Radiation polymerizationSwellingDrug release

references

查看原文

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Fabrication of microporous polymethacrylimide using γ-rays irradiation and characterization of its properties

Radiation preparation and characterization of temperature- and pH-sensitive hydrogel of N-isopropylacrylamide/β-cyclodextrin copolymer

The γ-irradiation stability of anhydrous ethylenediamine

Radiation polymerization and controlled drug release of P(NIPA−co−HEMA) and PNIPA/P(HEMA) IPN hydrogels

PREPARATION OF REINFORCED POLY (ETHYLENE OXIDE) BLEND HYDROGEL FILMS CONTAINING A DRUG AND ASSESSMENT OF THEIR PROPERTIES

Related Author

No data

Related Institution

Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics

School of Material Science and Technology, Southwest University of Science and Technology

School of Environmental and Chemical Engineering, Shanghai University

Institute of Nuclear Physics and Chemistry in Chinese Academy of Engineering Physics

College of Materials Engineering, Zhengzhou University

⁰

暂无标题

DOI：

摘要

Abstract

关键词

Keywords

references